ServicesEquipment Installation
Pool Equipment Installation in Gold Canyon
When a pump, filter or heater is done, we put in a replacement that fits your pool and your plumbing. We size it right, set it level, plumb it clean and show you how to keep it running. You get gear that lasts instead of gear that just works for now.
New Equipment, Put In to Last
Most pool equipment does not wear out on its own schedule. It wears out early because it was the wrong size, plumbed with tight elbows, or left sitting in standing water. We install pumps, filters, heaters, heat pumps, salt chlorine generators and automation with the next ten years in mind.
Sometimes a repair is the better call. If a $40 part will keep your pump going, we will say so and send you to our pool repair work instead. When replacement makes sense, we explain why in plain words and give you options that fit your pool, not the biggest unit on the truck.
Desert sun is hard on plastic housings and wiring. We set equipment so it is easy to service, protected where we can, and easy for you to check on.
What We Install
- Pool pumps
- Single-speed, two-speed and variable-speed pumps. Variable-speed models can run slow and quiet most of the day, which cuts power use and strain on the motor. We match the pump to your pipe size and filter so it is not fighting the system.
- Filters
- Cartridge, sand and DE filters. We size the filter to the pump's flow so it catches dirt without building up pressure too fast.
- Heaters and heat pumps
- Gas heaters and electric heat pumps for longer swim seasons. We check gas line size or electrical capacity before anything gets ordered.
- Salt chlorine generators
- Salt cells and control boxes, set up so the cell is easy to pull and clean. Hard water scale is the main thing that shortens a cell's life, so we show you what to watch for.
- Automation and controls
- Timers and automation panels that run your pump, heater and lights on a schedule. Good scheduling alone can add years to a pump.
- Booster pumps and plumbing
- Booster pumps for pressure-side cleaners, plus new valves, unions and PVC runs where the old plumbing is cracked or poorly laid out.
Signs It May Be Time for New Equipment
A loud or screeching pump
Grinding or high-pitched noise usually means worn motor bearings. Bearings can sometimes be replaced, but on an older motor a new pump is often the smarter spend.
Filter pressure that will not settle
If pressure climbs right after a cleaning, the filter may be undersized or the internals may be failing. Our filter cleaning visit is a good first check.
Cracked housings or constant leaks
Sun-baked plastic gets brittle. A cracked pump or filter housing tends to get worse, not better.
A heater that will not light or keep heat
Repeated ignition faults or error codes on an aging heater often point to replacement.
Power bills that keep going up
An old single-speed pump running eight hours a day uses a lot of electricity. Switching to variable speed is one of the few upgrades that can pay for itself.
What Moves the Price
Every install is priced after we see your equipment pad. The unit itself is only part of it. Plumbing, power and how hard the old gear is to get out all play a role, and we list each piece in the quote.
Type and size of unit
A variable-speed pump costs more than a single-speed. A heat pump costs more than a small gas heater. Bigger pools need bigger equipment.
Plumbing changes
Moving from one pipe size to another, adding valves or redoing a messy layout adds labor and parts.
Electrical or gas work
New circuits, longer gas lines or upgraded wiring can be needed for heaters and some pumps.
Access and removal
Tight side yards, equipment behind walls or very old gear that has to be cut out takes more time.
How an Install Day Goes
- 1
Look before we quote
We come out, check your current equipment, pipe size, pool volume and power or gas supply. Then we give you a free quote with the options laid out.
- 2
Order the right parts
Once you pick a unit, we order it along with the fittings and valves the job needs. If a permit applies to your install, we tell you up front and handle it.
- 3
Swap and plumb
We shut off power, remove the old unit and set the new one level on its pad. Plumbing gets glued with long-radius fittings where we can, so water moves with less resistance.
- 4
Start up and test
We prime the system, check for leaks, set flow and pressure, and program any timer or automation. We run it long enough to be sure it is steady.
- 5
Walk you through it
We show you the controls, the normal pressure reading and what basic care looks like. Old equipment gets hauled away and the pad is left clean.
Equipment Installation Questions
Should I repair my pump or replace it?
It depends on the age of the motor and what failed. A seal or capacitor is often worth fixing. If the motor is old and the bearings are going, a new variable-speed pump usually makes more sense over time. We will tell you which way we would go and why.
Is a variable-speed pump really worth it?
For most pools that run daily, yes. It can run at low speed for most of the day, which uses far less power and is easier on the motor. It is also much quieter.
How long does an install take?
Most pump or filter swaps are done in a few hours. Heaters, salt systems and automation can take most of a day, especially if plumbing or power needs work. We give you a time estimate with your quote.
Can I keep using my pool during the install?
You can swim while we work on the pad, but the pump will be off for part of the day. Once we start it back up and test it, everything is ready to use.
Do you install equipment I already bought?
Tell us the make and model when you call. If it fits your pool and system, we can talk about it. If it is the wrong size, we will let you know before we put it in.
Get Equipment That Fits Your Pool
Tell us what is going on with your pump, filter or heater. We will come look and give you straight options with a free quote.